JoeCustoms.com https://joecustoms.com/forums/ |
|
The Wraith car + driver and Rughead pg 4! https://joecustoms.com/forums/viewtopic.php?f=14&t=45978 |
Page 1 of 4 |
Author: | 2DARK2C [ Sun Jul 23, 2017 9:45 pm ] |
Post subject: | Re: The Wraith car |
sculpting up front |
Author: | 2DARK2C [ Sun Jul 23, 2017 9:50 pm ] |
Post subject: | Re: The Wraith car |
sculpting up top and rear |
Author: | 2DARK2C [ Sun Jul 23, 2017 9:53 pm ] |
Post subject: | Re: The Wraith car |
and with my figure wip still a lot to do. firstly sand/shape. then paint! |
Author: | 2DARK2C [ Sun Jul 23, 2017 9:58 pm ] |
Post subject: | Re: The Wraith car |
source pics |
Author: | sgcaper [ Tue Jul 25, 2017 10:42 pm ] |
Post subject: | Re: The Wraith car |
Wow! That is impressive. Really nice work on everything. |
Author: | 2DARK2C [ Tue Jul 25, 2017 11:04 pm ] |
Post subject: | Re: The Wraith car |
thanks sgcaper! it has been on my list since I started customizing! so many starts and fails, but I think this one might get finished! |
Author: | DarkJedi [ Wed Jul 26, 2017 12:00 am ] |
Post subject: | Re: The Wraith car |
I showed my Mom this thread as an example of how talented and skillful the members of this board are. I wasn't sure where this custom was going (and I don't recognize the actual car), but seeing the mods and work to get there is simply amazing. This is why I like this hobby. The ability to create a new character or vehicle by breathing new life into parts is inspiring. |
Author: | pluv [ Wed Jul 26, 2017 2:05 pm ] |
Post subject: | Re: The Wraith car |
Are you going to go back in and cut in the hood vents? |
Author: | 2DARK2C [ Wed Jul 26, 2017 7:23 pm ] |
Post subject: | Re: The Wraith car |
DarkJedi wrote: I showed my Mom this thread as an example of how talented and skillful the members of this board are. I wasn't sure where this custom was going (and I don't recognize the actual car), but seeing the mods and work to get there is simply amazing. This is why I like this hobby. The ability to create a new character or vehicle by breathing new life into parts is inspiring. Thank you DarkJedi ! that truly means a lot. you should check out the movie "The Wraith" it is pure 80's cheese on top of science fiction. basically it is the story of an alien like ghost back on earth for vengeance in a mid engine super car that fell from the sky. |
Author: | 2DARK2C [ Wed Jul 26, 2017 7:40 pm ] |
Post subject: | Re: The Wraith car |
pluv wrote: Are you going to go back in and cut in the hood vents? I should have sculpted them in , but I was more focused on getting the rough profile of the nose to my liking. it is far from screen accurate so I might apply some other detail there. i'm back and forth about sculpting the door areas. the source has small side ducts (air intake to cool engine) but I kind of like the large duct that the top and bottom pieces created. |
Author: | OreoBuilder [ Wed Jul 26, 2017 9:06 pm ] |
Post subject: | Re: The Wraith car |
Holey spacollies. This this is all kinds of awesome. I can't wait to see the rest. OB |
Author: | Blood Brigade [ Thu Jul 27, 2017 6:18 am ] |
Post subject: | Re: The Wraith car |
Is the driver going to fit in the car? That's going to be an epic challenge to get it straight and not wavey especially if your going black. Cool project I vagley remember that movie. |
Author: | past nastification [ Thu Jul 27, 2017 11:13 am ] |
Post subject: | Re: The Wraith car |
Wow. That's wild. How many hours so far? |
Author: | 2DARK2C [ Thu Jul 27, 2017 7:14 pm ] |
Post subject: | Re: The Wraith car |
thanks oreobuilder! i'm not planning on fitting the figure in, there is no scenes of the car being driven iirc just a few of the driver stepping out. the sci-fi aspect almost portrays the car and driver as one entity. you should watch it again Blood Brigade! thanks past nastification! this try was pretty quick. I chopped the nose off the base, taped on the black top piece and did the two rounds of sculpting all in two evenings. maybe 4 hrs not including taking all the screws out of the base! |
Page 1 of 4 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |